Wireless PCI Karte HILFE !!!!!

Moin
Ich suche jemanden der mir bei der Installation der EDIMAX 7628lG
helfen kann .
Ich habe Open SUSE 10.2 und 2.6.18.8-0.3 Kernel.

Die Karte hat zwar Linux Treiber aber ich steig da nicht so richtig durch.
In der Anleitung sprechen die von Module aber wo ?

LG Uwe

Anlietung hab ich mal hochgeladen!

* README
*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*

=======================================================================
ModelName:
===========
rt61


=======================================================================
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.


=======================================================================
Description:
=============
This is a linux device driver for Ralink RT61 a/b/g WLAN Card.



=======================================================================
Contents:
=============
./2.4x : Makefile for kernel 2.4 series
./2.6x : Makefile for kernel 2.6 series
*.c : c files
*.h : header files
Makefile.RTL865x : Makefile for big endian platform



=======================================================================
Features:
==========
This driver implements basic IEEE802.11. Infrastructure and adhoc mode with open or shared or
WPA-PSK authentication method. NONE, WEP, TKIP and AES encryption.



=======================================================================
Build Instructions:
====================
For 2.4 series kernel:
a. $tar -xvzf RT61_Linux_STA_Drv_x.x.x.x.tar.gz
go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.

b. Use 'chmod' command to change access right of following script files :
'load', 'unload', 'Configure'

c. run 'cp ../2.4x/Makefile .'
d. $make config # config build linux os version

e. $make all # compile driver source code

f. $cp RT2561.bin /etc/Wireless/RT61STA/ # copy firmware
$cp RT2561S.bin /etc/Wireless/RT61STA/
$cp RT2661.bin /etc/Wireless/RT61STA/

g. $load # load/insmod module(rt61.o)

Note: Script functionality:
load load module to kernel
unload unload module from kernel
Configure retrieve linux version


For 2.6 series kernel:
a. run 'cd STA/Module'
'cp ../2.6x/Makefile .'

b. $make all

c. $cp RT2561.bin /etc/Wireless/RT61STA/ # copy firmware
$cp RT2561S.bin /etc/Wireless/RT61STA/
$cp RT2661.bin /etc/Wireless/RT61STA/

d. run '/sbin/insmod rt61.ko' (as root)
'/sbin/ifconfig ra0 inet YOUR_IP up'


For big endian platform:
a. replace Makefile with Makefile.RTL865x



=======================================================================
CONFIGURATION:
====================
RT61 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file

i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)copy configuration file "RT61STA.dat" to /etc/Wireless/RT61STA/RT61STA.dat.


Configuration File : RT61STA.dat
---------------------------------------
# Copy this file to /etc/Wireless/RT61STA/RT61STA.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use "vi -b RT61STA.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
# The word of "Default" must not be removed
Default
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WpaPsk=abcdefghijklmnopqrstuvwxyz
TXBurst=0
PktAggregate=0
TurboRate=0
WmmCapable=0
AckPolicy1=0
AckPolicy2=0
AckPolicy3=0
AckPolicy4=0
BGProtection=0
ShortSlot=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0

-----------------------------------------------
*NOTE:
WMM parameters
WmmCapable Set it as 1 to turn on WMM Qos support
AckPolicy1~4 Ack policy which support normal Ack or no Ack
(AC_BK, AC_BE, AC_VI, AC_VO)

All WMM parameters do not support iwpriv command but ��WmmCapable����,
please store all parameter to RT61STA.dat, and restart driver.

-----------------------------------------------
syntax is 'Param'='Value' and describes below.

1. CountryRegion=value
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10, 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel

2. CountryRegionForABand=value
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel

3. SSID=value
value
0~z, 1~32 ascii characters.

4. WirelessMode=value
value
0: 11b/g mixed,
1: 11B only,
2: 11A only
3: 11a/b/g mixed
4: 11G only

5. TxRate=value
value
0: Auto //WirelessMode=0~4
1: 1 Mbps //WirelessMode=0 or 1 or 3
2: 2 Mbps //WirelessMode=0 or 1 or 3
3: 5.5 Mbps //WirelessMode=0 or 1 or 3
4: 11 Mbps //WirelessMode=0 or 1 or 3
5: 6 Mbps //WirelessMode=0 or 2 or 3 or 4
6: 9 Mbps //WirelessMode=0 or 2 or 3 or 4
7: 12 Mbps //WirelessMode=0 or 2 or 3 or 4
8: 18 Mbps //WirelessMode=0 or 2 or 3 or 4
9: 24 Mbps //WirelessMode=0 or 2 or 3 or 4
10: 36 Mbps //WirelessMode=0 or 2 or 3 or 4
11: 48 Mbps //WirelessMode=0 or 2 or 3 or 4
12: 54 Mbps //WirelessMode=0 or 2 or 3 or 4

6. Channel=value
value
1~14 depends on CountryRegion

7. BGProtection=value
value
0: Auto
1: Always on
2: Always off

8. TxPreamble=value
value
0:Preamble Long
1:Preamble Short
2:Auto

9. RTSThreshold=value
value
1~2347

10. FragThreshold=value
value
256~2346

11. TxBurst=value
value
0: Disable
1: Enable

12. NetworkType=value
value
Infra: infrastructure mode
Adhoc: adhoc mode

13. AdhocOfdm=value
value
0: Adhere WIFI spec, the Tx MAX rate will be 11Mbps in Adhoc mode
1: Violate WIFI spec, the Tx MAX rate will be 54Mbps in Adhoc mode(b/g mixed)
2: Violate WIFI spec, the Tx MAX rate will be 54Mbps in Adhoc mode(11g only)

14. AuthMode=value
value
OPEN For Open System
SHARED For Shared key System
WEPAUTO
WPAPSK
WPANONE For Adhoc Security System

15. EncrypType=value
value
NONE For AuthMode=OPEN
WEP For AuthMode=OPEN or AuthMode=SHARED
TKIP For AuthMode=WPAPSK
AES For AuthMode=WPAPSK

16. DefaultKeyID=value
value
1~4

17. Key1=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd

18. Key2=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd

19. Key3=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd

20. Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd

21. WPAPSK=value
value
8~63 ASCII or
64 HEX characters

22. PktAggregate=value
value
0: Disable
1: Enable when the peer supports it

23. TurboRate=value
value
0: Disable
1: Enable 72/100 Mbps whenever applicable
(Not support yet!)

24. WmmCapable=value
value
0: Disable WMM
1: Enable WMM

25. PSMode=value
value
0: CAM Constantly Awake Mode
1: Max_PSP Max Power Savings
2: Fast_PSP Power Save Mode

26. IEEE80211H=value
value
0: Disable
1: Enable Spectrum management
(This field can be enable only in A band)


MORE INFORMATION
=================================================================================
If you want for rt61 driver to auto-load at boot time:
A) choose ra0 for first RT61 WLAN card, ra1 for second RT61 WLAN card, etc.

B) create(edit) 'ifcfg-ra0' file in /etc/sysconfig/network-scripts/,
edit( or add the line) in /etc/modules.conf:
alias ra0 rt61

C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-ra0
DEVICE='ra0'
ONBOOT='yes'


NOTE:
if you use dhcp, add this line too .
BOOTPROTO='dhcp'

*D) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network

 

Das ist alles viel zu kompliziert. Lohnt sich das für dich?

Ich habe früher auch SuSE Linux ausprobiert und hatte regelmäßig Schwierigkeiten mit dem Wireless LAN (die Treiber sind proprietäre Software und deswegen in kargen Distributionen nicht enthalten!).

Bei Ubuntu gibt's da seit der 7.04-Version keinerlei Probleme mehr (zumindest mit den allermeisten WLAN-Modulen und WLAN-Sticks!).

Du kannst dir Ubuntu übrigens kostenlos und versandkostenfrei aus den Niederlanden schicken lassen. Guckst du: shipit.ubuntu.com - und ab die Post!

Schönen Abend noch!

freddiecarlton